Messages

1

VoxCommando Basics and Core Features / Re: Two problems with VC

« on: October 17, 2014, 12:34:46 AM »

Could something as simple as low batteries cause this? I have never seen or used the amulet remote. Just a guess.

2

What is a good microphone for speech recognition? / Re: Kinect 360

« on: October 03, 2014, 12:11:59 AM »

Thanks James and Naomi. Much appreciated.

3

What is a good microphone for speech recognition? / Re: Kinect 360

« on: October 02, 2014, 04:46:14 PM »

To all of you using a kinect how do you get around the sound from music or a movie interfering? For example if I am watching a movie via xbmc the OSD keeps popping up. Of course no commands are triggered because I have prefix mode on. Still annoying though to have it pop up every few seconds.

4

General Discussion / Re: about Viv

« on: August 13, 2014, 10:25:14 PM »

Looks like some pretty cool stuff.

5

General Discussion / Re: Smart Watch

« on: June 25, 2014, 09:55:37 AM »

Thanks for the advice, James. I will hold off for a while and just keep using my phone.

6

General Discussion / Re: Smart Watch

« on: June 20, 2014, 04:03:24 AM »

Thanks for the response James. So I would need something like in the link below? 300.00 sounds a little pricey. Or is that not a little pricey for this watch?

http://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_ff3=2&pub=5575087721&toolid=10001&campid=5337488338&customid=&icep_item=121363685877&ipn=psmain&icep_vectorid=229466&kwid=902099&mtid=824&kw=lg

7

General Discussion / Smart Watch

« on: June 13, 2014, 07:51:47 PM »

I found this on ebay. Just wondering if anyone here has used this with VC? If so how was the performance?

http://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_ff3=2&pub=5575087721&toolid=10001&campid=5337488338&customid=&icep_item=141296123060&ipn=psmain&icep_vectorid=229466&kwid=902099&mtid=824&kw=lg

8

General Discussion / Re: EULA On Start Up

« on: May 21, 2014, 01:28:47 AM »

Wasn't asking for a guessing game. Was simply asking if re-installing VC and importing my back up files would work ok? Nothing at all has changed. No new software, virus protection, no new downloads, no hardware changes, etc. Sorry for the miscommunication. I should have been more clear I suppose.

9

General Discussion / Re: EULA On Start Up

« on: May 20, 2014, 10:23:32 PM »

Luckily I have the files backed up. So just to a fresh install of VC and reload the files?

10

General Discussion / EULA On Start Up

« on: May 20, 2014, 10:11:49 PM »

Just turned computer on and launched VC. Instead of VC launching to my custom configuration I get the pop up below. Running VC 1.1.9.1 on Windows 8.1. I noticed also it does not give me an option to select a preconfigured set up.

11

General Discussion / Re: Getting VC To Read

« on: May 02, 2014, 11:13:13 PM »

Kalle. Thanks once again. It seems being that I am still a rookie VC user and obviously not as smart as some others on here I did not realize that was a command and not command group. However I am getting to the point where I am scared to ask for any help on here. It seems that when I do I get cut down pretty hard. I do not have the experience as most on here. I am still in very early learning stages. Once again thanks for your patience and help.

12

Other Plugins / Re: Google Calendar plugin update

« on: May 02, 2014, 07:09:19 PM »

This is only for VC2 users?

13

General Discussion / Re: Getting VC To Read

« on: May 02, 2014, 03:46:54 AM »

pmdaniels73, I too did not encounter any issues pasting the above embedded xml into VCv1.9.3.1
I know nothing of robobrowser so just affirmed the pasting xml into the MDI/Command Tree Editor part.
I'd suggest perhaps making a secondary install someplace another folder/machine real quick just to see if you can reproduce or perhaps provide screencap
You're not even getting / providing any error, which anytime I tried to paste and it failed I believe a descriptive error was presented to me.

I tried a different install on this machine. Then tried on another machine. Still no luck. Below is a video I posted to show exactly what the steps are that I am taking.

https://www.youtube.com/watch?v=pMVM1_URR38&feature=youtu.be

14

General Discussion / Re: Getting VC To Read

« on: May 02, 2014, 02:56:06 AM »

pmdaniels73, I too did not encounter any issues pasting the above embedded xml into VCv1.9.3.1
I know nothing of robobrowser so just affirmed the pasting xml into the MDI/Command Tree Editor part.
I'd suggest perhaps making a secondary install someplace another folder/machine real quick just to see if you can reproduce or perhaps provide screencap
You're not even getting / providing any error, which anytime I tried to paste and it failed I believe a descriptive error was presented to me.

You are correct. I am not getting any error messages. I am getting ready to try your suggestions now though to see if it works.

15

General Discussion / Re: Getting VC To Read

« on: May 02, 2014, 01:51:16 AM »

I know robo browser and regex things a bit tricky and I'm sure you will never find out how you can use it in the right way, so it is very appreciate that Naomi create and post a ready to use COMMAND, which you must only copy in a COMMAND-GROUP and that the Robot Browser plugin must be enabled in VC is also described above.
I think what James mean that you ask often for a ready to use solution without reading the forum rules first - if anyone bought a car from you and then he ask you a day later - "the car which I bought from you doesn't run, why?" - This question contains no information about what he have done - so there are many possibilities for what it could be.

I have test the command above and it works fantastic - good Job Naomi

Kalle

Thanks Kalle! I am not real sure on what else to explain. The process I went through is pretty simple. All I done was copied the command that is posted above. Then went into my tree editor. Then right clicked within the tree and clicked on paste. When I done this the command did not show up in the tree. That's it.