Messages

1

General Discussion / Re: Arduino udp or serial monitor trigger event???

« on: March 09, 2020, 12:15:13 PM »

Ok

2

General Discussion / Re: Arduino udp or serial monitor trigger event???

« on: March 09, 2020, 11:55:30 AM »

well you are right i setting my digital pins to HIGH before setting them to OUTPUT
because i copy it from the original code
this the original code :

Code: [Select]

int sw1 = 0; int sw11 = 0; int sw21 = 0;
int sw2 = 0; int sw12 = 0; int sw22 = 0;
int sw3 = 0; int sw13 = 0; int sw23 = 0;
int sw4 = 0; int sw14 = 0; int sw24 = 0;
int sw5 = 0; int sw15 = 0; int sw25 = 0;
int sw6 = 0; int sw16 = 0; int sw26 = 0;
int sw7 = 0; int sw17 = 0; int sw27 = 0;
int sw8 = 0; int sw18 = 0; int sw28 = 0;
int sw9 = 0; int sw19 = 0; int sw29 = 0;
int sw10 = 0; int sw20 = 0; int sw30 = 0;
int sw31 = 0; int sw41 = 0; int sw51 = 0;
int sw32 = 0; int sw42 = 0; int sw52 = 0;
int sw33 = 0; int sw43 = 0; int sw53 = 0;
int sw34 = 0; int sw44 = 0;
int sw35 = 0; int sw45 = 0;
int sw36 = 0; int sw46 = 0;
int sw37 = 0; int sw47 = 0;
int sw38 = 0; int sw48 = 0;
int sw39 = 0; int sw49 = 0;
int sw40 = 0; int sw50 = 0;


void setup() {
 pinMode(22, OUTPUT);     pinMode(32, OUTPUT);     pinMode(42, OUTPUT);     pinMode(52, OUTPUT);
  pinMode(23, OUTPUT);     pinMode(33, OUTPUT);     pinMode(43, OUTPUT);     pinMode(53, OUTPUT);
  pinMode(24, OUTPUT);     pinMode(34, OUTPUT);     pinMode(44, OUTPUT);
  pinMode(25, OUTPUT);     pinMode(35, OUTPUT);     pinMode(45, OUTPUT);
  pinMode(26, OUTPUT);     pinMode(36, OUTPUT);     pinMode(46, OUTPUT);
  pinMode(27, OUTPUT);     pinMode(37, OUTPUT);     pinMode(47, OUTPUT);
  pinMode(28, OUTPUT);     pinMode(38, OUTPUT);     pinMode(48, OUTPUT);
  pinMode(29, OUTPUT);     pinMode(39, OUTPUT);     pinMode(49, OUTPUT);
  pinMode(30, OUTPUT);     pinMode(40, OUTPUT);     pinMode(50, OUTPUT);
  pinMode(31, OUTPUT);     pinMode(41, OUTPUT);     pinMode(51, OUTPUT);
 

  digitalWrite(22, HIGH);    digitalWrite(32, HIGH);    digitalWrite(42, HIGH);    digitalWrite(52, HIGH);
  digitalWrite(23, HIGH);    digitalWrite(33, HIGH);    digitalWrite(43, HIGH);    digitalWrite(53, HIGH);
  digitalWrite(24, HIGH);    digitalWrite(34, HIGH);    digitalWrite(44, HIGH);
  digitalWrite(25, HIGH);    digitalWrite(35, HIGH);    digitalWrite(45, HIGH);
  digitalWrite(26, HIGH);    digitalWrite(36, HIGH);    digitalWrite(46, HIGH);
  digitalWrite(27, HIGH);    digitalWrite(37, HIGH);    digitalWrite(47, HIGH);
  digitalWrite(28, HIGH);    digitalWrite(38, HIGH);    digitalWrite(48, HIGH);
  digitalWrite(29, HIGH);    digitalWrite(39, HIGH);    digitalWrite(49, HIGH);
  digitalWrite(30, HIGH);    digitalWrite(40, HIGH);    digitalWrite(50, HIGH);
  digitalWrite(31, HIGH);    digitalWrite(41, HIGH);    digitalWrite(51, HIGH);

 Serial.begin(9600);
}
void loop() {
  if (Serial.available() > 1) {
    int input = Serial.read() ;

    Serial.println( input, DEC);
 
    if (input == 'A') {
      digitalWrite(22, sw1);
      sw1 = !sw1;
    }
      if (input == 'B'){
        digitalWrite(23, sw2);
      sw2 = !sw2;
  }
            if (input == 'C'){
              digitalWrite(24, sw3);
      sw3 = !sw3;
}
            if (input == 'D'){
              digitalWrite(25, sw4);
      sw4 = !sw4;
}
            if (input == 'E'){
              digitalWrite(26, sw5);
      sw5 = !sw5;
}
            if (input == 'F'){
              digitalWrite(27, sw6);
      sw6 = !sw6;
}
            if (input == 'G'){
              digitalWrite(28, sw7);
      sw7 = !sw7;
}
            if (input == 'H'){
              digitalWrite(29, sw8);
      sw8 = !sw8;
}
            if (input == 'I'){
              digitalWrite(30, sw9);
      sw9 = !sw9;
}
            if (input == 'J'){
              digitalWrite(31, sw10);
      sw10 = !sw10;
}
             if (input == 'K'){
               digitalWrite(32, sw11);
      sw11 = !sw11;
}
             if (input == 'L'){
               digitalWrite(33, sw12);
      sw12 = !sw12;
}
             if (input == 'M'){
               digitalWrite(34, sw13);
      sw13 = !sw13;
}
             if (input == 'N'){
               digitalWrite(35, sw14);
      sw14 = !sw14;
}
             if (input == 'O'){
               digitalWrite(36, sw15);
      sw15 = !sw15;
}
             if (input == 'P'){
               digitalWrite(37, sw16);
      sw16 = !sw16;
}
             if (input == 'Q'){
               digitalWrite(38, sw17);
      sw17 = !sw17;
}
             if (input == 'R'){
               digitalWrite(39, sw18);
      sw18 = !sw18;
}
             if (input == 'S'){
               digitalWrite(40, sw19);
      sw19 = !sw19;
}
             if (input == 'T'){
               digitalWrite(41, sw20);
      sw20 = !sw20;
}
             if (input == 'U'){
               digitalWrite(42, sw21);
      sw21 = !sw21;
}
             if (input == 'V'){
               digitalWrite(43, sw22);
      sw22 = !sw22;
}
             if (input == 'W'){
               digitalWrite(44, sw23);
      sw23 = !sw23;
}
             if (input == 'X'){
               digitalWrite(45, sw24);
      sw24 = !sw24;
}
             if (input == 'Y'){
               digitalWrite(46, sw25);
      sw25 = !sw25;
}
             if (input == 'Z'){
               digitalWrite(47, sw26);
      sw26 = !sw26;
}
             if (input == '1'){
               digitalWrite(48, sw27);
      sw27 = !sw27;
}
             if (input == '2'){
               digitalWrite(49, sw28);
      sw28 = !sw28;
}
             if (input == '3'){
               digitalWrite(50, sw29);
      sw29 = !sw29;
}
             if (input == '4'){
               digitalWrite(51, sw30);
      sw30 = !sw30;
}
             if (input == '5'){
               digitalWrite(52, sw31);
      sw31 = !sw31;
}
             if (input == '6'){
               digitalWrite(53, sw32);
      sw32 = !sw32;
             }
  }
}

3

General Discussion / Re: Arduino udp or serial monitor trigger event???

« on: March 09, 2020, 11:43:32 AM »

Also you attached your arduino code two times but did not attach your python code.

i have bad internet i attach it but it show i didnt that way sorry for that

about the VoxLog.txt file i attach it

4

General Discussion / Re: Arduino udp or serial monitor trigger event???

« on: March 09, 2020, 11:32:07 AM »

Hi James
I don't have python code 
I just send arduino code to help me with it
I don't know how to make it work 

5

General Discussion / Re: Arduino udp or serial monitor trigger event???

« on: March 09, 2020, 10:49:53 AM »

This is a iPhone image format, but what do you want show us?
You can hover your mouse over the orange messages in the VC history window which contain some information what goes wrong.

6

General Discussion / Re: Arduino udp or serial monitor trigger event???

« on: March 09, 2020, 10:42:28 AM »

Hi kale
Did you see the attach file
There is no event there you are right
where the stars I but I need event to trigger  to vc

7

General Discussion / Re: Arduino udp or serial monitor trigger event???

« on: March 09, 2020, 10:01:57 AM »

sorry
i send it again

8

General Discussion / Re: Arduino udp or serial monitor trigger event???

« on: March 09, 2020, 09:46:39 AM »

this what i want to do

please check the attach bellow

9

General Discussion / Re: Arduino udp or serial monitor trigger event???

« on: March 08, 2020, 07:53:06 PM »

When arduino send the event it's not showed VC history I mean the event

10

General Discussion / Re: Arduino udp or serial monitor trigger event???

« on: March 08, 2020, 06:58:52 PM »

I tried but it not work with me maybe I missed something   

11

General Discussion / Arduino udp or serial monitor trigger event???

« on: March 08, 2020, 02:36:51 PM »

Hi all

How can I make arduino monitor for example (temperature or water level) if reaches a certain limit then trigger event for example (event&&WaterLevelLow )or(event&&HighTemp) to VC through serial the easiest and semple way

12

General Discussion / Re: My project Jarvis

« on: November 25, 2018, 01:18:31 AM »

Thank you for your help

13

General Discussion / Re: My project Jarvis

« on: November 24, 2018, 10:01:01 AM »

Hi all

Is there any way to make arduino trigger event to voxcommando
Anyone can help me

14

General Discussion / Re: My project Jarvis

« on: November 10, 2018, 08:13:52 AM »

Thanks kalle 😎👍
I finish it at one ☝️ month August it was ready
And believe me its very hard to work in August in my country (kingdom of Bahrain )
The temperature 50c to 58c 😰😰

15

General Discussion / Re: My project Jarvis

« on: November 10, 2018, 06:47:38 AM »

Thank you PegLegTV

Well believe it or not it’s salvage car
i take the challenge and Convert it to Jarvis and I did it 😎👍
https://youtu.be/UMWoI0Hw4MQ