Recent Posts

Pages: 1 ... 3 4 [5] 6 7 ... 10

BEAM IR/RF Wifi transceiver / Re: BEAM documentation / news

« Last post by jitterjames on December 17, 2022, 10:45:21 AM »

normally noise should be set lower (maybe 5) and increasing the "Equal +/-" to about 10 is going to help your compressed codes. You see your values of 38, 41, 40, 42. Those are probably all the same duration and the Equal +/- will allow VC to see that they are all the same and change them all to the average of their values. So they will all be set to something like 40, and then replaced with a letter.

BEAM IR/RF Wifi transceiver / Re: BEAM documentation / news

« Last post by Kalle on December 16, 2022, 02:50:16 PM »

Thanks for all the info.

If the second code was work for you, it is easy to shorten all you codes without an math or regec or what ever.
The only thing you have to do - take a look where is the large number is and cut it out to the last number before the next similar large number starts (include thecomma at the end).

example:

~~123,41,121,41,120,122,41,41,120,122,41,41,120,122,41,121,41,41,121,42,120,42,120,43,119,43,120,123,40,42,120,43,120,42,~~1201,57,106,53,110,128,36,125,38,124,39,123,40,122,41,41,121,42,120,43,119,123,40,42,120,122,41,42,120,122,41,121,42,41,121,42,120,42,120,42,120,43,119,123,40,42,120,42,120,42,1201,56,107,53,110,128,36,125,38,124,39,123,40,122,41,41,121,42,120,42,120,122,41,42,120,122,41,41,120,122,41,121,42,41,121,41,121,42,120,42,120,42,120,122,41,42,120,42,121,42,1201,56,107,52,111,128,36,125,38,124,39,122,40,122,41,41,121,42,120,42,120,122,41,41,120,122,41,41,121,122,41,121,42,40,121,41,121,42,120,42,120,42,120,122,41,41,120,42,121,42,1201,56,107,52,111,128,36,125,38,124,39,123,40,122,41,41,121,42,120,42,120,122,41,42,120,122,41,41,121,121,41,121,42,41,121,41,121,42,120,42,120,42,120,122,41,41,121,42,120,42,1201,56,107,52,111,128,36,125,38,124,39,122,40,122,41,41,121,42,120,42,120,122,41,41,121,122,41,41,121,121,41,121,42,40,121,41,121,42,121,42,120,42,120,122,41,41,121,42,121,42,1201,56,107,52,111,128,36,125,38,124,39,123,40,122,41,41,

This is your posted raw code and you can see the correct sequence ist starting at green and repeatedly continuous - the red marked is the code is not needed.

Kalle

BEAM IR/RF Wifi transceiver / Re: BEAM documentation / news

« Last post by PegLegTV on December 16, 2022, 02:06:17 PM »

I tested both codes that you posted, only the second code worked.

I did some testing with the beam plugin

Beam Settings:
Lock Min: 100
Lock Max: 5000
Noise: 40 (any higher and no codes show up)
Equal +/-: 2

Beam Plugin Raw RF code:

Code: [Select]

http://192.168.1.202/learnRFraw?lmin=100&lmax=5000&nt=40
Data: 123,41,121,41,120,122,41,41,120,122,41,41,120,122,41,121,41,41,121,42,120,42,120,43,119,43,120,123,40,42,120,43,120,42,1201,57,106,53,110,128,36,125,38,124,39,123,40,122,41,41,121,42,120,43,119,123,40,42,120,122,41,42,120,122,41,121,42,41,121,42,120,42,120,42,120,43,119,123,40,42,120,42,120,42,1201,56,107,53,110,128,36,125,38,124,39,123,40,122,41,41,121,42,120,42,120,122,41,42,120,122,41,41,120,122,41,121,42,41,121,41,121,42,120,42,120,42,120,122,41,42,120,42,121,42,1201,56,107,52,111,128,36,125,38,124,39,122,40,122,41,41,121,42,120,42,120,122,41,41,120,122,41,41,121,122,41,121,42,40,121,41,121,42,120,42,120,42,120,122,41,41,120,42,121,42,1201,56,107,52,111,128,36,125,38,124,39,123,40,122,41,41,121,42,120,42,120,122,41,42,120,122,41,41,121,121,41,121,42,41,121,41,121,42,120,42,120,42,120,122,41,41,121,42,120,42,1201,56,107,52,111,128,36,125,38,124,39,122,40,122,41,41,121,42,120,42,120,122,41,41,121,122,41,41,121,121,41,121,42,40,121,41,121,42,121,42,120,42,120,122,41,41,121,42,121,42,1201,56,107,52,111,128,36,125,38,124,39,123,40,122,41,41,
Sequences detected: 1
LockMin: 100,  LockMax: 5000,  NoiseTheshold: 40

no compressed code.

Note: I would see some occasional compressed codes but when they showed up none of them worked, and neither did the raw code. So as I worked through the remote buttons if I saw compressed codes, the raw code didn't look like other codes that worked, so I wouldn't test it.

I only have one other remote that uses 433mhz (projector screen), and that remote never generated any compressed codes origianly. when I test it now, the raw code is much longer and causes VC to freeze short tearm and the beam to restart, but the raw code does work.

Projector Screen Remote Beam output:

Code: [Select]

http://192.168.1.202/learnRFraw?lmin=100&lmax=5000&nt=20
Data: 1090,123,21,117,29,112,33,38,105,37,105,107,38,33,108,106,38,105,38,33,109,34,109,106,38,105,39,32,110,105,39,33,109,105,38,33,109,105,38,33,109,33,109,34,108,34,108,106,38,33,1103,116,29,113,32,110,34,37,105,37,106,108,36,35,107,107,37,106,38,33,109,34,108,106,38,105,38,33,109,105,39,33,109,105,39,33,110,105,39,32,110,33,109,34,108,34,108,106,38,33,1103,116,29,113,32,111,33,37,105,37,106,108,36,35,107,107,37,106,38,33,109,34,108,106,38,105,38,33,109,105,38,33,109,105,38,33,109,105,39,33,109,33,109,34,108,34,108,106,38,33,1103,116,29,113,32,111,34,37,106,37,105,108,36,35,107,107,37,106,37,33,109,33,108,106,38,105,38,33,109,105,38,33,109,106,38,33,109,105,38,33,109,34,109,34,108,34,108,106,38,33,1103,116,29,113,32,110,34,37,105,37,106,108,36,35,107,107,37,106,38,33,109,34,108,106,38,105,38,33,110,105,38,33,109,105,38,33,109,105,38,33,109,34,109,34,108,34,108,106,38,33,1103,116,29,113,32,110,33,37,105,37,106,108,36,35,107,107,37,106,37,34,109,34,109,106,37,105,38,33,109,105,38,33,109,106,38,32,110,105,38,33,109,33,109,34,108,34,108,106,38,33,
Sequences detected: 1
LockMin: 100,  LockMax: 5000,  NoiseTheshold: 20

after looking over the code, there are six codes generated, all of them work, the first one is different and the last five are identical. with this remote the projector screen will beap when the button is pressed so I only press the button until I hear the beap which is a quick press of the button.

1090,123,21,117,29,112,33,38,105,37,105,107,38,33,108,106,38,105,38,33,109,34,109,106,38,105,39,32,110,105,39,33,109,105,38,33,109,105,38,33,109,33,109,34,108,34,108,106,38,33,

1103,116,29,113,32,110,34,37,105,37,106,108,36,35,107,107,37,106,38,33,109,34,108,106,38,105,38,33,109,105,39,33,109,105,39,33,110,105,39,32,110,33,109,34,108,34,108,106,38,33,
1103,116,29,113,32,111,33,37,105,37,106,108,36,35,107,107,37,106,38,33,109,34,108,106,38,105,38,33,109,105,38,33,109,105,38,33,109,105,39,33,109,33,109,34,108,34,108,106,38,33,
1103,116,29,113,32,111,34,37,106,37,105,108,36,35,107,107,37,106,37,33,109,33,108,106,38,105,38,33,109,105,38,33,109,106,38,33,109,105,38,33,109,34,109,34,108,34,108,106,38,33,
1103,116,29,113,32,110,34,37,105,37,106,108,36,35,107,107,37,106,38,33,109,34,108,106,38,105,38,33,110,105,38,33,109,105,38,33,109,105,38,33,109,34,109,34,108,34,108,106,38,33,
1103,116,29,113,32,110,33,37,105,37,106,108,36,35,107,107,37,106,37,34,109,34,109,106,37,105,38,33,109,105,38,33,109,106,38,32,110,105,38,33,109,33,109,34,108,34,108,106,38,33,

this remote does start with a higher number like your mentioned in your post.

these are the remotes that I'm testing with

Amazon: SUPERNIGHT RGB Light Strip Remote Controller, RF Remote
Amazon: Projector Screen

the LED RF Remote doesn't say if it is 433mhz or 315mhz, it was a black Friday sale $6.33 USD so I risked it, when the beam couldn't read the remote origianally, I ordered a remote that said it was 433mhz however even with the new RF receiver that remote never produced any codes with the beam so I returned it.

I'm sorry I know that that is a lot of information above, but I wanted to make sure you knew what I have tried and what the results were.

BEAM IR/RF Wifi transceiver / Re: BEAM documentation / news

« Last post by Kalle on December 15, 2022, 02:22:41 AM »

Now that makes me curious - I have a lot of 433MHz remotes and none of them produce such a start frequency. What I mean, your RF code starts with a relatively small sequence of numbers (initial code: 102,134,32,128,36,124,40,122,41, ...), which I have never seen before, no matter from which RF remote control - the initial code always starts with a large number.

I am in the lucky position to test your working code with two BEAM's and the BEAM Plugin (one BEAM transmits, one receives) and have the following result which you could try out.

/sendRFraw?code=1019,69,105,54B129,36DEDEDEE120EFEFDEEFDEEDDEDEEDEFEFCFEFDEEF45BDEDEDEDEFEB248,24DFCEDFEEDFEFEFEFEFEFEFEFEFEFEFEEFEFEFEFE

This is a part of your original code, which i have shortened:
/sendRFraw?code=1201,55,108,52,111,128,36,125,38,124,39,123,40,122,41,41,122,41,121,42,120,122,41,41,121,121,42,41,121,122,42,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,

In the Beam plugin there is the possibility to adjust the noise - try higher values, this will filter the sequences a bit or lower values to see more sequences but a lot of trash.
What surprises me is that you don't get anything in the BEAM plugin under "Compressed Code" when you try to learn the remote control with the BEAM.

Kalle

BEAM IR/RF Wifi transceiver / Re: BEAM documentation / news

« Last post by PegLegTV on December 14, 2022, 01:13:50 PM »

Kalle, sorry I forgot to respond to yours when I got back home. the raw codes that worked never produced anything on the bottom half of the screen like your showing in the picture, so it took me a little bit to spot when a raw code was good or not just had to look for the lenth and starting numbers.

After some testing I found that if I cut the raw code down to 96 integer groupings then the commands would work and not freeze VC and restart the beam

1 2 3 4 5
102,134,32,128,36

from there I made a command in VC so I could input the raw code and the remote button name and have it create a map table with the button names and code, along with testing the new raw code. from there it was fairly easy, all I had to do was repeat that 32 times for all the buttons I wanted to learn.

only four buttons where difficult to figure out (dim,brighter, faster, slower) but after some testing I relized that they need to be repeated multiple times in order to see a difference so I just added &n=9 to the end of the raw codes and the problem with those buttons were solved.

Jitterjames, I tested the raw code you posted and I also tried your code by adding &n=2 to the end of your command but still no luck, from what I can tell it seems that anything less than 96 integer groupings the codes would not work. however after looking at the raw code with your input I did find that the code repeats twice minus the big number.

Working Power on:

Code: [Select]

{M:IP.Beam 2.0}/sendRFraw?code=102,134,32,128,36,124,40,122,41,121,42,40,121,42,121,42,120,122,41,41,121,122,42,41,121,121,42,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,1201,55,108,52,111,128,36,125,38,124,39,123,40,122,41,41,122,41,121,42,120,122,41,41,121,121,42,41,121,122,42,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,

Raw code borken down
102,134,32,128,36,124,40,122,41,121,42,40,121,42,121,42,120,122,41,41,121,122,42,41,121,121,42,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,1201
,55,108,52,111,128,36,125,38,124,39,123,40,122,41,41,122,41,121,42,120,122,41,41,121,121,42,41,121,122,42,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,

Beam RF code shortner commands that I used

Code: [Select]

<?xml version="1.0" encoding="utf-16"?>
<!--VoxCommando 2.3.0.3-->
<commandGroup open="True" name="Beam RF Code Shortener" enabled="True" prefix="" priority="0" requiredProcess="" description="">
  <command id="1040" name="RF code shortener" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description="Action number 1 replace (PUT RAW RF CODE HERE) with your raw RF Code&#38;#xD;&#38;#xA;Action number 3 repeats X amout of times to set the length of the new raw code&#38;#xD;&#38;#xA;{1} = button name for the Maptable">
    <action>
      <cmdType>Results.SetVar</cmdType>
      <params>
        <param>NewCode</param>
        <param>(PUT RAW RF CODE HERE)</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>Results.RegEx</cmdType>
      <params>
        <param>(\d+)</param>
        <param />
        <param>{Var.NewCode}</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>Results.SetVar</cmdType>
      <params>
        <param>Desktop</param>
        <param>C:\Users\{Var.username}\Desktop\</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>File.Append</cmdType>
      <params>
        <param>{Var.Desktop}Code.txt</param>
        <param>{Match.{i}},</param>
      </params>
      <cmdRepeat>96</cmdRepeat>
    </action>
    <action>
      <cmdType>File.Read</cmdType>
      <params>
        <param>{Var.Desktop}Code.txt</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>Map.Set</cmdType>
      <params>
        <param>TEST</param>
        <param>{1}</param>
        <param>{LastResult}</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>File.Delete</cmdType>
      <params>
        <param>{Var.Desktop}Code.txt</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>Scrape</cmdType>
      <params>
        <param>{M:IP.Beam 2.0}/sendRFraw?code{M:TEST.{1}}</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
  </command>
  <command id="855" name="Short RF code Test" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description="{1} = Button name to test">
    <action>
      <cmdType>scrape</cmdType>
      <params>
        <param>{M:IP.Beam 2.0}/sendRFraw?code={M:TEST.{1}}</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
  </command>
  <command id="1108" name="Export TEST Map to new maptable and payload file" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description="{1} = New MapTable name that you want (no spaces)&#38;#xD;&#38;#xA;{2} = Payload.xml file name that you want (without  .xml) (stored in {Path.VC}\payloads)">
    <action>
      <cmdType>Map.ExportPayloadXML</cmdType>
      <params>
        <param>Payloads\TEST.xml</param>
        <param>TEST</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>File.Read</cmdType>
      <params>
        <param>{Path.VC}\Payloads\TEST.xml</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>Results.RegExSingle</cmdType>
      <params>
        <param>&lt;payload&gt;.*?&lt;value&gt;(.*?)&lt;/value&gt;.*?&lt;phrase&gt;(.*?)&lt;/phrase&gt;</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>Results.MatchToMap</cmdType>
      <params>
        <param>{1}</param>
        <param>True</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>Map.ExportPayloadXML</cmdType>
      <params>
        <param>Payloads\{2}.xml</param>
        <param>{1}</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>File.Delete</cmdType>
      <params>
        <param>{Path.VC}\Payloads\TEST.xml</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>Map.DropTable</cmdType>
      <params>
        <param>TEST</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
    <action>
      <cmdType>Map.CreateTable</cmdType>
      <params>
        <param>TEST</param>
      </params>
      <cmdRepeat>1</cmdRepeat>
    </action>
  </command>
</commandGroup>

Thank you guys for the help and input.

BEAM IR/RF Wifi transceiver / Re: BEAM documentation / news

« Last post by jitterjames on December 14, 2022, 12:10:03 PM »

If you break it down your code looks like this: You can see the pattern.
code=
102,134,32,128,36,124,40,122,41,121,42,40,121,42,121,42,120,122,41,41,121,122,42,41,121,121,42,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,1201
,55,108,52,111,128,36,125,38,124,39,123,40,122,41,41,122,41,121,42,120,122,41,41,121,121,42,41,121,122,42,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,1201
,55,108,52,111,128,36,125,38,124,40,122,40,122,42,41,121,42,121,42,120,122,41,41,121,122,42,41,121,121,41,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,1201
,55,108,52,111,128,36,125,38,124,40,122,40,122,41,41,121,41,121,42,120,122,41,41,121,122,42,41,121,121,42,120,43,40,122,41,121,41,121,42,121,42,120,122,41,41,121,42,120,42,1201
,55,108,52,111,128,36,125,38,124,39,123,40,122,41,41,121,42,120,42,120,122,41,41,121,122,41,41,121,122,41,121,42,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,1201
,56,108,52,111,128,36,125,38,124,39,123,40,122,41,41,121,42,120,42,120,122,41,41,121,121,42,41,121,121,42,121,42,40,122,41,121,42,121,42,120,42,120,122,41,41,121,42,120,42,1201
,55,108,52,

BEAM IR/RF Wifi transceiver / Re: BEAM documentation / news

« Last post by jitterjames on December 14, 2022, 12:02:20 PM »

You may only need up to the first larger number, possibly also setting n>1

eg:

Code: [Select]

{M:IP.Beam 2.0}/sendRFraw?code=102,134,32,128,36,124,40,122,41,121,42,40,121,42,121,42,120,122,41,41,121,122,42,41,121,121,42,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,1201

BEAM IR/RF Wifi transceiver / Re: BEAM documentation / news

« Last post by Kalle on December 10, 2022, 02:53:38 AM »

Hi PegLeg,
nice to hear that your problem is solved.
You can also send the compressed code instead of the raw code which is displayed in the BEAM plugin.

example code: /sendRFraw?code=1130,39,104ABABABABABABABABABABBAABABABABABABABBAABBAABABA

or an other option is to use the BEAM WebUI for learning a code (if it possible) and maybe you have a code that looks like: /sendRF?code=4116&bits=24&n=1

BEAM IR/RF Wifi transceiver / Re: BEAM documentation / news

« Last post by PegLegTV on December 09, 2022, 02:36:54 PM »

I got the new 433mhz chip set in yesterday and got the anttenas attatched. and it solved the problem.

I'm working on learning the codes for my RF Led strip Lights, the codes are extreamly long, the only working codes are the initial raw codes, and they cause the Beam to restart and VC to freeze for around 20 seconds after sending them.

I've tried adjusting settings to no avail.

current settings:
Lock Min: 100
Lock Max: 1202 (lowest it can be set or I don't get any codes)
Noise: 10
Equal: 2

I've tried adjusting all of the above settings, but I see the same results.

Raw Code for "power on" that works but causes the Beam to restart.

Code: [Select]

{M:IP.Beam 2.0}/sendRFraw?code=102,134,32,128,36,124,40,122,41,121,42,40,121,42,121,42,120,122,41,41,121,122,42,41,121,121,42,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,1201,55,108,52,111,128,36,125,38,124,39,123,40,122,41,41,122,41,121,42,120,122,41,41,121,121,42,41,121,122,42,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,1201,55,108,52,111,128,36,125,38,124,40,122,40,122,42,41,121,42,121,42,120,122,41,41,121,122,42,41,121,121,41,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,1201,55,108,52,111,128,36,125,38,124,40,122,40,122,41,41,121,41,121,42,120,122,41,41,121,122,42,41,121,121,42,120,43,40,122,41,121,41,121,42,121,42,120,122,41,41,121,42,120,42,1201,55,108,52,111,128,36,125,38,124,39,123,40,122,41,41,121,42,120,42,120,122,41,41,121,122,41,41,121,122,41,121,42,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,1201,56,108,52,111,128,36,125,38,124,39,123,40,122,41,41,121,42,120,42,120,122,41,41,121,121,42,41,121,121,42,121,42,40,122,41,121,42,121,42,120,42,120,122,41,41,121,42,120,42,1201,55,108,52,

Raw code for "power on" that I edited manualy, (I deleted two numbers at a time and tested each time until it failed, then used the last working code)
this code does not cause any problems, and turns on my strip lights

Code: [Select]

{M:IP.Beam 2.0}/sendRFraw?code=102,134,32,128,36,124,40,122,41,121,42,40,121,42,121,42,120,122,41,41,121,122,42,41,121,121,42,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,120,42,1201,55,108,52,111,128,36,125,38,124,39,123,40,122,41,41,122,41,121,42,120,122,41,41,121,121,42,41,121,122,42,121,43,40,122,41,121,41,121,42,120,42,120,122,41,41,121,42,

~~do you guys have any tips on how to shorten these codes so they don't cause the beam to restart and vc to freeze, other than manully editing them?~~

update: I created a VC Command to Shorten the codes. I was able to shorten all the codes so they don't cause the beeam to restart or cause VC to freeze.

thank you!

VoxCommando Basics and Core Features / Re: Voxcommando to control Android using ADB?

« Last post by monkee on December 07, 2022, 04:13:03 PM »

Quote from: PegLegTV on December 07, 2022, 02:23:51 PM

I tried this a few years back and wasn't able to get it to work.

you could look into Join by joaoapps and tasker, I'm not sure how well it will work as a remote structure though.

Join has a rest Api so you can use it with VC, I use it for notifications, and tasker actions.

your work flow might be something like this:

VC (Join API(Tasker actions)) > Tasker (on Shield TV) > Tasker send ADB cmd.

Join and Tasker are paid apps, I paid $3.00 USD each I believe.

Join Actions group:
Code: [Select]
<?xml version="1.0" encoding="utf-16"?>  <commandGroup open="False" name="Join - Notifications" enabled="True" prefix="" priority="0" requiredProcess="" description=""> <command id="746" name="Join Basic Notification" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description="{1}= Device Name&#38;#xD;&#38;#xA;{2}=Title&#38;#xD;&#38;#xA;{3}=Text&#38;#xD;&#38;#xA;{4}=Icon&#38;#xD;&#38;#xA;{5}=Notification Bar Icon"> <action> <cmdType>Tools.Encode.URI</cmdType> <params> <param>https://joinjoaomgcd.appspot.com/_ah/api/messaging/v1/sendPush?deviceNames={1}&text={3}&title={2}&icon={M:JoinNotification.{4}}&smallicon={M:JoinNotification.{4}Icon}&apikey={M:apiKeys.Join}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <action> <cmdType>Scrape</cmdType> <params> <param>{LastResult}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <event>Join.Notification</event> </command> <command id="809" name="Join Tasker Command" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description="{1}= Device Name&#38;#xD;&#38;#xA;{2}= Tasker command (text)"> <action> <cmdType>Tools.Encode.URI</cmdType> <params> <param>https://joinjoaomgcd.appspot.com/_ah/api/messaging/v1/sendPush?deviceNames={1}&text={2}&apikey={M:apiKeys.Join}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <action> <cmdType>Scrape</cmdType> <params> <param>{LastResult}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <event>Join.Tasker</event> </command> <command id="810" name="Join Tasker (all Androids)" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description="{1}= Tasker command"> <action> <cmdType>Tools.Encode.URI</cmdType> <params> <param>https://joinjoaomgcd.appspot.com/_ah/api/messaging/v1/sendPush?deviceId=group.android&text={1}&apikey={M:apiKeys.Join}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <action> <cmdType>Scrape</cmdType> <params> <param>{LastResult}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <event>Join.Tasker.Group</event> </command> <command id="817" name="Join android App" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description="{1}= Device Name&#38;#xD;&#38;#xA;{2}= App Name"> <action> <cmdType>Tools.Encode.URI</cmdType> <params> <param>https://joinjoaomgcd.appspot.com/_ah/api/messaging/v1/sendPush?deviceNames={1}&app={2}&apikey={M:apiKeys.Join}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <action> <cmdType>Scrape</cmdType> <params> <param>{LastResult}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <event>Join.Android.App</event> </command> <command id="846" name="Join Set Device Clipboard" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description="{1} Device name&#38;#xD;&#38;#xA;{2} Tasker "Event""> <action> <cmdType>Tools.Encode.URI</cmdType> <params> <param>https://joinjoaomgcd.appspot.com/_ah/api/messaging/v1/sendPush?deviceNames={1}&clipboard={2}&apikey={M:apiKeys.Join}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <action> <cmdType>Scrape</cmdType> <params> <param>{LastResult}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <event>Join.Clipboard</event> </command> <command id="812" name="Join Say" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description="{1}= Device Name&#38;#xD;&#38;#xA;{2}= What to say"> <action> <cmdType>Tools.Encode.URI</cmdType> <params> <param>https://joinjoaomgcd.appspot.com/_ah/api/messaging/v1/sendPush?deviceNames={1}&say={2}&apikey={M:apiKeys.Join}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <action> <cmdType>Scrape</cmdType> <params> <param>{LastResult}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <event>Join.Say</event> </command> <command id="789" name="Join set volume Android Devices" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description=""> <action> <cmdType>Scrape</cmdType> <params> <param>https://joinjoaomgcd.appspot.com/_ah/api/messaging/v1/sendPush?deviceId=group.android&mediaVolume=100&ringVolume=100&alarmVolume=100&apikey={M:apiKeys.Join}</param> </params> <cmdRepeat>1</cmdRepeat> </action> </command> <command id="844" name="Join Link" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description="NOTIFICATION&#38;#xD;&#38;#xA;{1}=Device Name&#38;#xD;&#38;#xA;{2}=Title&#38;#xD;&#38;#xA;{3}=Text&#38;#xD;&#38;#xA;{4}=Icon&#38;#xD;&#38;#xA;{5}=url"> <action> <cmdType>Tools.Encode.URI</cmdType> <params> <param>https://joinjoaomgcd.appspot.com/_ah/api/messaging/v1/sendPush?deviceNames={1}&text={3}&title={2}&url={5}&dismissOnTouch=true&icon={M:JoinNotification.{4}}&smallicon={M:JoinNotification.{4}Icon}&apikey={M:apiKeys.Join}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <action> <cmdType>Scrape</cmdType> <params> <param>{LastResult}</param> </params> <cmdRepeat>1</cmdRepeat> </action> <event>Join.Link</event> </command> </commandGroup>
there are multpile commands in the group above they will all require your Join API key,

replace {M:apiKeys.Join} with your API Key

Thanks so much for the additional options, I'll let you know if I get it working, one way or another!

Pages: 1 ... 3 4 [5] 6 7 ... 10